Deze Rockamp NiMH-batterij met maar liefst 4000 mAh is veelzijdig en de ideale oplossing voor mensen met een krap budget. Of het nu wordt gebruikt in voertuigen, boten, vliegtuigen, startbakken of andere accessoires, de batterij blijft krachtig en levert voldoende stroom onderweg. Sluit de AKku eenvoudig aan op het gewenste apparaat via de 14 AWG-kabel met T-plug en u bent klaar om te gaan. Als u nog meer flexibiliteit nodig heeft, zult u ook verrast worden door een korte adapterkabel met Tamiya-stekker.

Specificaties:

Productinformatie "Robitronic Storage and Transport Bag"

De transporttas is gemaakt van hoogwaardig en resistent materiaal. Binnenin is de tas versterkt met een plastic inzetstuk en verdeeld in twee gebieden met een tussenbodem. Door het gebruik is het gemakkelijk schoon te maken, zelfs oliën hebben geen kans om naar buiten te dringen. Aan de rechterkant heeft de tas ook een kleiner compartiment met klittenbandklep. Transport kan worden gedaan via de praktische schouderriem of de draaggreep aan de bovenkant.

De buitenschaal is gemaakt van een extreem duurzaam en robuust nylon en is bestand tegen zelfs de wildste toepassingen. Dit materiaal is ook zeer gemakkelijk schoon te maken.

Specificaties:

Leveringsomvang:
1x zak
1x binneninzet
1x schouderriem
(levering als bouwpakket, montage in een mum van tijd en zonder gereedschap)

KoPropo Steering Sponge Hard

KoPropo Steering Sponge

Product information "Flysky R4P ANT Receiver 4CH"

The R4P receiver is the ideal partner when using a Flysky remote control and is specially designed for the installation and output of PWM signals. Therefore it is supported by all ANT-capable transmitters.

Technical Specifications

Product information "Flysky FGr4S AFHDS3 Receiver 4CH"

The FGr4S receiver is the ideal support when using a Flysky remote control. The receiver makes use of a technology used by several Flysky transmitters - the automatic frequency hopping digital system (short: AFHDS3). With a bidirectional transmission system via the antenna, this receiver is specially designed for the installation and output of PWM/PPM/i-BUS and S.BUS signals. All AFHDS3-capable transmitters are supported.

Technical Specifications

Product information "Flysky Noble NB4 with 2 Receiver"

With the NB4 radio remote control from FlySky, driving an RC car or boat offers as much comfort as it offers technical specifications. After all, the remote control uses the new and extremely flexible AFHDS3 protocol for transmission while being ergonomically design.

In combination with this protocol, the advantages of a wireless WS2A system and the new 2.4GHz chip, a wide variety of transmitter parameters can be set dynamically. This includes channel number, channel resolution, range, anti-interference requirements and also latency. This makes it possible to freely adjust the transmitter to Your own needs via the 3.5 inch TFT display. The real-time data exchange between the transmitter and the receiver also enables increased control over the flight model with constantly updated information on temperature and speed, for example.

Features:

• Advanced and modern radio
• Ergonomic design with turnable wheel
• Suitable for both right and left handers
• Dual Battery System
• Intelligent RF configuration
• Less than 3ms latency
• Also suited for simulators and games without using an external dongle via USB

Technical Specificatons:

Delivery:

• FlySky "NB4" Transmitter
• Reveiver: FGr4 and FGr4S
• USB data cable
• Grip shell
• Springs (S, L)
• 2x transparent protection sticker
• Manuals

Product information "Flysky Noble NB4-Pro with 2 Receiver"

The Noble Pro breaks traditional standards with new ideas and offers extensive setting options for racers, crawlers and other RC vehicles. This 18CH transmitter with 7 channel modes is ideal for any terrain and shows top performance even in the most difficult situations. In addition, the new 2CH "Extreme Mode" with a new frequency algorithm ensures unimagined performance with only little delay.

The most striking feature of the FlySky Noble Pro is the holder for smartphones and the steering wheel, the position of which can be changed so that both left and right-handers can get the best out of their vehicle all the same. Together with the comfortable shape of the handle, this is definitely an extremely ergonomic transmitter overall.

Features:

• Set consisting of over 20 parts such as transmitter, 2x receiver, case and much more
• Ideal for any off-road use, whether on-road, off-road or on the water
• 5 mixing setting options and speed segmentation for optimal adaptation to every riding requirement
• And three built-in high-performance chips for great performance
• Variety of structural personalization options (e.g. different throttle levers, springs, steering wheels, ... )
• Suitable for both right and left handers
• With 4 PWM and 8 PWM receivers as required
• Including 2 exchangeable batteries for 8 hours of action each
• Wireless charging station for convenient energy refueling
• Easy to use touch menu

Technical Specifications Transmitter:

Technical Specifications Receivers:

Delivery:

• FlySky "Noble Pro" transmitter
• Receivers: FGr4B and FGr8B
• Hard case including key
• USB data cable
• Wireless charging station
• Grip shell (XL)
• Wrist strap
• Steering wheel and sponge (L)
• 1.5mm and 2.5mm wrench
• Brake pad set
• Thread adjusting screw
• Knob
• Springs (S, L)
• Throttle (S, L, Plastic)
• Back & angle bracket
• Sticker (company logo, various)

•  Do you have any questions concerning this product?

54318, TBLE-015 Sensor Cable 160mm

54317, TBLE-01S Sensor Cable 120mm

Tamiya primer grijs

Grondspray voor plastic en metalen onderdelen in model en hobby. De grijze Tamiya grondspray dekt uitstekend.

• Kleur: grijs-mat
• Inhoud 180ml
• Zonder lood, zware metalen en CFK's

TRF 42352 Clamp Type Alum Hubs NarTrd (4)

- Smalle wielnaven met loopvlakklem zijn een populaire keuze voor toerwagenmodellen.
- Gebruik een smaller profiel aan de voorkant voor een scherpere stuurreactie, aan de achterkant voor meer grip of zelfs over de hele auto!
- Aluminium onderdelen hebben de iconische Tamiya blauw geanodiseerde afwerking.
- Bevat vier hubs, plus vijf 1,6x4mm kolomschroeven.

Compatibel chassis
TA06, TA06 PRO, TA06 MS, TA07 PRO, TA07 MS, TB-04, TB-04 PRO, TB-05 PRO, TB Evo.6, TB Evo.6 MS, TB Evo.7, TRF419, TRF419X, TRF419XR, TRF420 & TT-02 Type-S chassis

* Voor gebruik met 24 mm brede (medium-smalle) wielen. Artikelen 53646 en 54573 zijn mogelijk vereist.

Tamiya 22073 XV-02 Carbon bumpersteun

- 2mm dikte koolstofvezel bumpersteun x1
- Rubber bussen x2
- 6mm borgpennen x2
- 3x16mm ronde inbusschroeven x2
- Compatibel met XV-02 chassis auto's.
- Carbon fiber patronen geven uw model een stijlvolle racy look

Mon-Tech P9X8 LMH 1:10 Body (ongeverfd)

De nieuwe P9X8 is gebaseerd op de Peugeot 9X8, die rijdt in de Hyper Car LMH-serie.
De nieuwe P9X8 kan worden gemonteerd op alle toerwagens van de nieuwste generatie en op de Formule1 met een wielbasis van 260 mm.

De carrosserie wordt ongelakt geleverd, inclusief voorruitmaskers en stickervellen!

Praktische verlengkabel voor servo's of controllers met de normale, gemeenschappelijke JR-connector. Als de originele kabel te kort is en je niets wilt solderen, zijn deze kabels van MR33 de perfecte oplossing!

Verkrijgbaar in lengtes van 50mm, 75mm, 100mm, 125mm, 150mm, 175mm en 200mm!

Praktische verlengkabel voor servo's of controllers met de normale, gemeenschappelijke JR-connector. Als de originele kabel te kort is en je niets wilt solderen, zijn deze kabels van MR33 de perfecte oplossing!

Verkrijgbaar in lengtes van 50mm, 75mm, 100mm, 125mm, 150mm, 175mm en 200mm!

Praktische verlengkabel voor servo's of controllers met de normale, gemeenschappelijke JR-connector. Als de originele kabel te kort is en je niets wilt solderen, zijn deze kabels van MR33 de perfecte oplossing!

Verkrijgbaar in lengtes van 50mm, 75mm, 100mm, 125mm, 150mm, 175mm en 200mm!

Praktische verlengkabel voor servo's of controllers met de normale, gemeenschappelijke JR-connector. Als de originele kabel te kort is en je niets wilt solderen, zijn deze kabels van MR33 de perfecte oplossing!

Verkrijgbaar in lengtes van 50mm, 75mm, 100mm, 125mm, 150mm, 175mm en 200mm!

Praktische verlengkabel voor servo's of controllers met de normale, gemeenschappelijke JR-connector. Als de originele kabel te kort is en je niets wilt solderen, zijn deze kabels van MR33 de perfecte oplossing!

Verkrijgbaar in lengtes van 50mm, 75mm, 100mm, 125mm, 150mm, 175mm en 200mm!

Praktische verlengkabel voor servo's of controllers met de normale, gemeenschappelijke JR-connector. Als de originele kabel te kort is en je niets wilt solderen, zijn deze kabels van MR33 de perfecte oplossing!

Verkrijgbaar in lengtes van 50mm, 75mm, 100mm, 125mm, 150mm, 175mm en 200mm!

Praktische verlengkabel voor servo's of controllers met de normale, gemeenschappelijke JR-connector. Als de originele kabel te kort is en je niets wilt solderen, zijn deze kabels van MR33 de perfecte oplossing!

Verkrijgbaar in lengtes van 50mm, 75mm, 100mm, 125mm, 150mm, 175mm en 200mm!

Tamiya Set van 4 Slick A

Artikelnummer: 53433-SET
EAN: 0086544915789

Omschrijving:
Set van 4 banden Slick A geschikt voor o.a. Tamiya Cup Euro TW.

Set bestaande uit:
- 2 x 53433 Slick A
- 2 x 53435 Insert hard
- 1 x 54852 1:10 Velgen (4) 18-Sp. Geel 24mm

Leveringsomvang:
- 1 Set Tamiya Set van 4 Slick A

51078, DF02 D-Parts Bumper/Body Mount

Based on the latest SWORKz S35-GTE platform, SWORKz further developed and improved thenitro GT and came up with the S35-GT. The S35-GT is the ultimate SWORKz 1/8th nitro On-Road GT Car at this moment. Its front and rear suspension design is shared with the S35-GTE. The Ackermann steering system came directly from the 1/8th S35-3 nitro Buggy. A new center 2 speed on-road transmission system gives perfect acceleration to the S35-GT. The S35-GT newly designed arms are made from a strong nylon material. Optional carbon covers are available to adjust the arm’s stiffness for different tracks. The new unique front shock tower design allows to change the front upper angle position easily. The T-7075 aluminum chassis with its new design L.F.C (Lower Friction Coefficient) system will give more grip and at the same time less friction for the rear. A new radio tray system provides better and more precise throttle and braking response.

Features:

• New T7075 Hard Anodized, Lightend Aluminium Chassis
• New Wide Chassis Design
• New Lower Shock Towers
• New Shorter Shock Bodies
• New Shorter Shock Shafts
• New Shock Caps
• New Shorter Front Shock Springs
• New Fixed Shock Spring Holder
• New 3mm Updated Rear Shock Studs
• New Ackerman Plate
• New Steering System
• New Servo Saver Aluminium Part
• New Servo Saver Fixable Nut
• New Servo Saver Plate
• New Servo Saver Post Locking Design
• New Steering Balls
• New Steering Knuckle Plates
• New Updated Toe In Plates with Square Inserts
• New Lightweight Wing Mount
• New Side Guards
• New Lower Front and Rear Arms
• New Body Posts Front and Rear
• New Composite Rear Hubs with Carbon Plates
• New Multi Adjustable Ball System for Rear Upper Arms
• New Anticlock Screws for Shocks
• New Aerodinamically Optimized Body Shell
• 3 HET Differentials Included
• 2 Front Chassis Braces Included
• Black Competition Shock Springs Included
• Adjustable Wing Position
• Adjustable Wing Angle
• More Balance Weight Positions
• Stronger Downstop Area
• Optimized Composite Material
• Aluminium Parts in T7075

Specifications:

1up Racing Pink Ball Diff Grease - 3g

Formulated with extensive testing from our Factory Drivers and made for modern high-grip indoor racetracks, we are excited to introduce 1up Racing Pink Ball Diff Grease! Our super tacky Ball Diff Grease gives you the on-power steering and high-speed stability needed to push your buggy with confidence and shave away at your lap times. Like all of our greases, 1up Pink is proudly Made in the USA and backed with the 1up Racing Guarantee – Love it or we’ll return it. Pick one up today!

Follow these instructions to build  a buttery-smooth diff that lasts!

Step 1) Clean the outdrives, diff rings, diff balls, thrust rings, thrust balls and diff screw with parts cleaner to ensure they are free of any machining oils or burrs.

Step 2) Apply 1up Pink to the outdrives and install the diff rings.

Step 3) Apply a heavy amount of 1up Pink to the diff rings and outdrive surface area as shown.

Step 4) Pack 1up Pink into the diff gear and install the diff balls.

Step 5) Build the thrust assembly with 1up Gold as shown.

Finish the diff assembly per your instruction manual and set to a very light tension that just allows the diff movement to engage. Wipe away and save any excess 1up Pink that squeezes out.

Break-in is crucial, allow 30-40 minutes to complete these steps. With the car on a stand and no tires installed, insert the tip of a wrench into either outdrive slot and push through to lock the diff movement on that side. Turn on the car and set your throttle center point so the transmission begins rotating slowly. The opposite outdrive should be spinning. After 2-3 minutes turn down the throttle trim so the outdrive stops spinning, switch the wrench to the other side and repeat.

After both sides have spun at a very light tension for 2-3 minutes each, stop the transmission, tighten the diff screw 1/4 turn and repeat. Gradually tighten the screw after each tension has been broken in until you reach the desired setting. Charge up the battery and run the car on track for 3-4 minutes. Adjust the diff if needed and you’ll be good to go!

Xray Stickers For Body 5 Different Colors, X397320

Xray X4 Alu Steering Plate 7.5mm For Dual Steering

Connector : XT90H Female plug 

Connector : XT90I 2+2 with cap Female plug (5pcs)

Connector : Molex 2P Female plug (10pcs)

 Connector : Molex 2P Female plug with 100mm 22awg cable (1pcs)

Connector : male JST (10pcs)

Connector : female JST (10pcs)

- 10-spaaks schotelvelgen
- 0mm offset, 4 stuks
- voor 24 mm brede banden
- Compatibel met 1/10 toerwagens
 

Beschrijving:Set van 4 banden Slick A geschikt voor bijvoorbeeld Tamiya Cup Euro TW

Set bestaande uit:- 2 x 53433 Slick A


- 2 x 53435 Insert Hard
- 1 x 54850 1:

10 velgen (4) Y-Sp. Geel 24mm +

2 Leveringsomvang:
- 1 set Tamiya set van 4 Slick A

Hobbywing Seaking Cooling Tube 3660 For 540er Motor

Hobbywing Ezrun Sl 56118sd G2 800kv 4pol, 8mm For 1:5

Hudy Parts Case - 275 X 180mm

Hudy Tape, H209062

Hudy Alu Countersunk Servo Shim (10)

Hudy Alu Countersunk Servo Shim - Black (10)

Hudy Pit Mat Full Color 650x1200mm

Xray Composite Steering Plate - Front/rear Mounting Positions - Graphite

Xray Composite Front Bumper

Xray Xb8'23 Incl Fx K303 & 2169 Muffler - 1/8 Luxury Nitro Off-road Car Combo

Xray 3bb Clutch Bell 14t - Lightweight + 3x Ball-bearing

Xray X4f'24 Graphite Upper Deck - Split Rear - 2.0mm

Xray X4f'24 Graphite Upper Deck - Split Front - 2.0mm